Community Hack to Increase MicroSD Card

This is not a recommended hack as it will void your warranty. I am including the information here since the original post does not have comment thread anymore.

Increase your Ricoh Theta S Storage - Will Void Warranty

by replacing it’s micro SD card

Ricoh Theta S camera is a camera able to capture 360-degree panoramas in one click.

Very well made and pretty good quality for the price, one of its main advantage is to be able to capture a 360 degree panorama every 8 seconds and then turn them into timlelapse.

But Ricoh has chosen to use a 8Gb internal storage, which represents about 1600 views …

1600 panoramas represents 3:30 hours of shooting and hardly a minute of film at 30 frames per second.

It’s frustrating not being able to capture a place during one day long, you can increase the duration of use with external batteries (the camera can be recharged during operation), but the 8Gb internal memory will be full very quickly.

Roberto Leone who paved the way by opening the famous Theta S realized that as his little sister (the M15) it used a micro SD card (8Gb Transcend) as internal storage, which could be replaced with a larger capacity.

If Ricoh had opted for an access door to this card would have made life easier, but here is a step by step tutorial how to replace the micro SD card from your Ricoh Theta S with a larger capacity, at your own risk (open your camera manufacturer will void its warranty …)

STEP 1 - Remove the cover (Definitely not authorized by RICOH)

Using a knife or a very thin screwdriver remove the plastic cover glued under the camera

Once removed you will find four small Phillips screws.

STEP 2 - Remove the screws

Remove the four screws.

STEP 3 - Open the Theta S and VOID YOUR WARRANTY

Pull the opposite part of the case to the usb and HDMI jacks. You can help yourself with plastic utensil to pry . Don’t be afraid to pull , the case is fermemant clipped .

STEP 4 - Remove the trim - (You may break your camera)

Nothing special here.

STEP 5 - Remove the screws

Remove the four screws.

STEP 6 - Remove the pcb board

Be careful not to bend the ribbon cable.

STEP 7 - Remove tthe battery

The battery is tapped, so don’t be afraid to pull it hard. But don’t bend the connexions

STEP 8 - Remove the trim

Nothing special here.

STEP 9 - Peel off the foil.

The micro SD card is under :wink:

STEP 10 - Push on the SD card.

You have to push on the SD card to disengage from its location, don’t pull on it !

STEP 11 - Remove the screws

Remove the two screws holding the left edge of the camera to get out the SD card.

STEP 12 - Remove the SD card

Pull down the camera cover to be able to remove the 8Gb SD card.

STEP 13 - Remove the SD card

Pull down the camera cover to be able to remove the 8Gb SD card.

STEP 14 - Increase the storage

Replace the micro SD card with a bigger one (haven’t tried more than 32Gb) and format it FAT32.

STEP 15 - Reassemble the camera

Follow the steps in reverse order and don’t forget to reposition this small part.

IT’S ALIVE !

Turn your Ricoh Theta S to check that everything works well.

READY FOR TIMELAPSE !

A 32GB card will let you capture over 6000 panoramas of 5376X2688 pixels!


# Original Post

Other information

From mbirth
By the way, the used MicroSD card is an industry-grade MLC card which is more stable than the cards you can buy in stores.

From me in a different discussion

Actually, the guy Boby Brown that had the problem got it to work with a Samsung evo 32gb orange card, class 10. He basically copied the exact same setup as the first guy, Jerome Baccon-Gibod. Amazing that they’re willing to void their warranties this way. Not sure why they don’t just use the API to delete the images on the camera and download it to an external disk

Note: A FAT32 partition cannot be created that is larger than 32GB.
A file cannot be transferred to a FAT32 partition if the file is larger than 4GB.

1 Like

Thanks. So this is a bit of a problem with larger videos over 4GB, right? Does the MicroSD card need to be FAT32, or do you think it can be exFAT?

It is no idea to use a 64GB SD card when you have to make 2 Partitions on it
here below are a image from Image Capture on a mac the video are 25min 1,4GB 1280x720
i docent think a1920x1080 become over the 4GB limit
we shot a video simultaneous with a AS200V Action Cam XAVC format SD card
1920x1080 50 frames p.sek 25min Video file size 10GB
exFAT (Extended File Allocation Table) is a MS format i docent think the Camera will recognize the card then.
A THETA 4K version runs into trouble extending the 4GB limit

1 Like

Great guide! My only request is that it would be helpful if the Theta was always oriented in the same direction (lens on the left because that is how it’s easiest to remove the SD card ?), if possible, in all the pics so that people won’t get “turned around” when assembling/re-assembling.

There was a point during re-assembly that I had laid out my screws in the position that i removed them (the 4 screws (1 silver, 3 black), but because certain pictures had been rotated, I almost put them in the wrong way during re-assembly.

Thanks!

1 Like

Also, I believe Step 15 has an incorrect picture - I think the metal “washer” goes over the black piece and not under it. If you see Step 9, it appears the silver metal piece goes between the screw and the black plastic “hole”

2 Likes

Thanks for your contribution to the knowledge pool. :theta:

1 Like

Also, would be nice to see a picture of the 4 screws (1 silver, 3 black) of Step 5 and how they align with the holes. Per my last comment, my placement may have been incorrect. I’ll try to add in a picture of the 4 screws (1 silver, 3 black) and how I think they’re aligned in my next upgrade, but if someone is doing an SD upgrade in the future, if they could take a pic of which screws go where, that could be useful to future users.

but it seems to be possible to format greater volumes with this GUI
http://www.ridgecrop.demon.co.uk/index.htm?guiformat.htm

By the way if you know exactly where the micro Sd card is situated in the camera
is there any reason to take the camera apart
just Dremel a slot on the exact spot and replace the card

1 Like

I wish i could Dremel a slot. I know where it is and I have a Dremel, but for some reason, I’m more comfortable opening and unscrewing screws than with slicing open a slot. Maybe one day, I’ll get the guts to do it; possibly if I had a walkthrough guide that i know works =)

Also, I did originally use Fat32Formatter for the initial 64GB I tried with no luck. To be fair, I used Fat32Formatter (Quick Format) on a Samsung Orange 32GB (known to work) card and that also did not work. I THEN tried windows format (right click, Format), and also used Quick Format with the 32GB Samsung Orange card and that also did not work. Hopefully if I find a combination that works, I’ll post it here for the community. My next attempt will be to uncheck “quick format” and try that.

A member of the THETA Developers Beta forum “dhanainme” Finally,I formatted the card in an other Camera (a Sony A6000) and inserted the card to Theta. this alone worked.for him
https://developers.theta360.com/en/forums/viewtopic.php?f=5&t=1898#p4349

My sony DSLR a77 creates a folder structure on the SD card
PRIVATE/SONY
PRIVATE/AVCHD/BDMV
CLIPINF
PLAYLIST
STREAM
INDEX.BDM
MOVIEOBJ.BDM

i think any Sony camera with SD slot can format the micro SD with a SD to micro SD adapter
we use 32 GB SanDisk Ultra 80MB/s SDHC I clas10

2 Likes

That’s a nice find. There’s a lot of good information there, including this bit:

curl -X POST http://192.168.1.1/osc/state
{"fingerprint":"FIG_0027","state":{"sessionId":"SID_0004", "batteryLevel":1.0,"storageChanged":false,"_captureStatus":"idle","_recordedTime":0,"_recordableTime":0,"_latestFileUri":"100RICOH/R0010004.JPG","_batteryState":"disconnect","_cameraError":["CARD_DETECT_FAIL","FORMAT_CARD"]}}

The key bit of information being this line:

cameraError":["CARD_DETECT_FAIL","FORMAT_CARD"]}}

The other really interesting thing is that the person used a different camera to format the microSD card.

2 Likes

I just completed a battery replacement and inserted a 128 gb micro and crossed my fingers. It works fine!

2 Likes

Amazing! @Rick_Borman, can you list your parts? For example, the exact battery and microsd card would be great if you have the information handy.

Also, if you have any pictures of your build, that would be wonderful.

This is a great example of community members helping out each other to extend the life of equipment. There’s really no other way of changing the battery except these high-risk, high-reward, DIY projects.

Great news that your project was successful.

1 Like

Thanks for reaching out. You are 100% correct that it is high-risk hight reward. The unit is persnickety, delicate and the screws are unnaturally small.

I used the PowerExtra 3.7v 1500mAh 5.55Wh battery that was posted on the blog. Amazon

The memory was a last minute cross-fingers try. I used a PNY 128gb micro Elite XC 1 .

I will also add this info to the thread.

I must admit that the unit does not look as tight as it did before disassembly. That said, it is certainly functional and for my purposes as better instrument.

Best

Rick

Rick Borman

3 Likes

Super cool! I’d really love to see pictures, too, from the hack, if you have any.

1 Like